Optical Multiplexer with 4 T1 interfaces, Single Mode Fiber, AC and DC Power
$715.00
In stock
Description
DESCRIPTION
The O-9310 can multiplex up to 4 T1 or E1 signals for transmission over an optical fiber, resulting in longer reach without repeaters and superior performance compared to copper media.
The O-9310 also supports an optional 10 /100 BaseT ethernet bridge port, an optional V.35, X.21, RS449/V.36, RS232/V.28 or EIA530 or EIA530(A) with DTE/DCE selection.
Available in a cost-effective non-CPU model with DIP switch setup or an intelligent model with SNMP and remote configuration capability. Basic non-manageable model without CPU provides system setup and loopback by DIP switches setting. Application for the Optical T1/E1 extender include fiber connected extensions for LAN, WAN, SONET/SDH, ATM and DLC.
SPECIFICATIONS
Optical Fiber Interface
Optical Fiber Characteristics
| Source MLM Laser System | Gain 30 dB | ||||
| Wavelength 1310 ± 50 nm, 1550 ± 40 nm | Line Code Scrambled NRZ | ||||
| Power -26 or -8 dBm | Detector Type PIN-FET | ||||
| Receiver Sensitivity -38 dBm at BER < 10-10 | Fiber Type Single mode | ||||
| Optical Line Rate 155.52Mbps | Protection Optional 1+1 APS | ||||
| 50 Km reach | NOTE: Longer or shorter, 15 to 120Km, on special order. | ||||
|
|
|||||
| Optical Module | Fiber Direction | Wavelength (nm) | Connector | Distance (km) | Power (dB) |
| Single | Dual uni-direction | 1310 | SC (Subscriber Connector) | 30 | 20 |
| 1310 | SC (Subscriber Connector) | 50 | 30 | ||
| 1310 | FC (Fiber Connector) | 30 | 20 | ||
| 1550 | SC (Subscriber Connector) | 20 | 12 | ||
| 1550 | SC (Subscriber Connector) | 100 | 40 | ||
|
|
|||||
| Single | Single bi-direction (master) | 1310/1550 | SC (Subscriber Connector) | 30 | 20 |
| Single bi-direction (slave) | 1310/1550 | SC (Subscriber Connector) | 30 | 20 | |
For discussion on whether to choose uni-directonal or bi-directional fiber option, see the white paper here.
E-1 Line Interface
| Number of E1 lines 4 | Impedance 120 ohm twisted pair, 75 ohm for BNC |
| Line Rate 2.048 Mbps +/- 50 ppm | Connector RJ48C, BNC |
| Line Code HDB3 | Output Signal ITU G.703 |
T-1 Line Interface
| Number of T1 lines 4 | |
| Line Rate 1.544 Mbps ± 50 bps | Output Signal DSX1 |
| Line Code AMI or B8ZS | Framing D4/ESF (selectable) |
| Input Signal ABAM cable length up to 655 feet | Connector RJ48C |
Bridge Interface
10/ 100 Mbps half/ full duplex ethernet bridging and 22 Mbps operation on the HDLC port
ANSI/ IEEE Std. 802.1D MAC Bridging capabilities (without spanning tree algorithm)
Automatic MAC table learning and aging
Supports VLAN and extended Ethernet frame support
DTE Interface |
|
| Port Number 1 | Connector DB25S |
| Data Rate Nx64kbps (N=1~32) | Clock Mode External, Internal, Received (Selectable) |
| Type Software-selectable V.35, X.21, RS449/V.36, RS232/V.28, EIA530 and EIA530A | |
| Connector RJ45 at rear panel | |
| Data Rate Up to 64Kbps async | |
Connector DE9 on front panel
Console |
SNMP |
| Protocol Telnet | |
| Electrical RS232 interface | Connector RJ45 on front panel |
| Protocol Menu driven VT-100 terminal | |
| Baud Rate 9600, 19200, 38400, 57600, 115200 |
Diagnostics Test
Optical Fiber Local and remote loopbacks
T1 and E1 Lines Local and remote loopbacks
Physical/Electrical
Dimensions 215 x 55 x 188 mm (W x H x D)
Mounting Stand-alone
Power Source (AC) 100 to 240 Vac, 50/ 60 Hz
Power Source (DC) 24Vdc: 18-36 Vdc ; 48Vdc: 36-72 Vdc
Power Consumption < 10 W
Temperature Range 0°C to 50°C
Humidity 0% – 95% RH (non-condensing)
Additional information
| Weight | 2 lbs |
|---|---|
| Dimensions | 5 × 5 × 5 in |
